Warning: Trying to access array offset on value of type bool in /www/doc/www.compuplast.tech/www/wp-content/plugins/edge-cpt/shortcodes/imagegallery/image-gallery.php on line 239

Warning: Trying to access array offset on value of type bool in /www/doc/www.compuplast.tech/www/wp-content/plugins/edge-cpt/shortcodes/imagegallery/image-gallery.php on line 239

Warning: Trying to access array offset on value of type bool in /www/doc/www.compuplast.tech/www/wp-content/plugins/edge-cpt/shortcodes/imagegallery/image-gallery.php on line 239
logo
A powerful architecture & Construction theme. Construct your website in the perfect Ratio.
Alienum phaedrum torquatos nec eu, vis detraxit periculis ex, nihil expetendis in mei. Mei an pericula
office@compuplast.tech
+420 577 220 451
Svat. Čecha 293, 760 01 Zlín
mobile logo

News

COMPUPLAST® SOFTWARE /  News

Optimize your Bubble Cooling

by Compuplast
News
3. 7. 2025

Are you involved in film blowing or stretch tube production? Are you facing challenges with bubble stability? Would you like precise data on temperatures, velocities, thicknesses, and other physical properties throughout the entire bubble length? The VEL™ system includes a specialized module for simulating bubble behavior during the film blowing (or tube stretching) process. This module enables you to: Design the bubble’s shape Optimize temperature development both along and across the bubble Estimate thickness, velocity, deformation, stress, and curvature Identify stability problems We are excited to...

New VEL™ 7.0 Extrusion Calculator Module

by Compuplast
Technical articles
16. 6. 2025

Compuplast’s complex and precise 2D and 3D finite element calculations are powerful CAE tools. However, in many situations, a faster estimate is needed — and often sufficient. That’s where simple 1D solvers can provide essential information for your redesign steps. The VEL™ 7.0 Extrusion Calculator is a set of lightweight CAE tools. It is simple to use, fast to solve, and easy to post-process, yet can still support the design of complex extrusion tooling. This calculator can be used as a socket...

Periodicity in VEL™ 7.0 3DFem module

by Compuplast
Technical articles
16. 6. 2025

Almost any type of extrusion die can be solved using the Compuplast VEL™ 7.0 3DFem module, including popular spiral mandrel dies and/or flat spiral dies. However, the geometry of these die types is periodic. Therefore, it is essential to take advantage of periodicity to speed up the solution process.Why solve the entire model if, for example, it contains 12 identical periodic sections? Why not solve just one of them—saving both time and memory? New in version 7.0, we have introduced support...

Extruzní seminář firmy COMPUPLAST® s možností testovací licence

by Compuplast
News, Seminars
22. 5. 2025

2-denní seminář 9. a 10. září (September) 2025; od 8:30 do 16:30 Místo konání: Konferenční místnosti č. 4  Obchodního domu Prior Zlín, náměstí Práce 2523, Zlín Cena: Dvoudenní seminář - CZK 26 100 nebo CZK 34 500 včetně 3-měsíční licence VEL™ Material Properties modulu (včetně Extrusion Calculator™) STRUČNÝ PŘEHLED Seminář vychází z praxe zaměřené na porozumění procesu vytlačování – od vlastností materiálů, praktického přístupu k návrhu a optimalizaci jednošneků, vytlačovacích hlav, chladících zařízení, až k řešení typických problémů při extruzi i koextruzi. Účastníci získají potřebné znalosti z reologie...

The Effect of Material Selection In Feed-block Coextrusion of a Three Layer Film

by Compuplast
Technical articles
21. 9. 2022

This paper describes a case study dealing with the development of a three-layer product on a feed-block coextrusion system. The problems or phenomena that occurred during the product development experiments are explained via flow simulation and the rheological properties of the materials used. The results of the study are compared with real film samples produced during the development Article can be downloaded here. ...

What is the appropriate boundary condition for temperature?

by Compuplast
Technical articles
21. 9. 2022

Flow inside a die can be simulated by most of Compuplast VEL™ modules. An axi-symmetric or planar flow inside a die can be simulated by using the 2DFem module, any profile die can be simulated by the 3DFem module, some profile dies and designed profile dies can be simulated by using the Profile die module, flat dies, spiral dies, flat spiral dies (stackable dies) or cross-head dies can be simulated by using the appropriate module. In all these modules the...

COMPUPLAST® Extrusion Seminar with Trial License

by Compuplast
News, Seminars
15. 6. 2022

2-Day Seminar Sep 20 - 21, 2022; 9 am - 4:30 pm Location: Comfort Hotel Prague City East, Becvarova 14, 100 00, Prague, Czech Republic Tuition: 2-day Seminar for EUR 2,100 or  2-day Seminar for EUR 2,550 including 3-month license of VEL™ Material Properties module (with Extrusion Calculator™) OVERVIEW This seminar will teach a systematic and practical approach to designing, optimizing and troubleshooting single-screw extruders and dies in extrusion process. Attendees will gain a good understanding of practical rheology and how to use it for efficient die design. Explaining...

Privacy Overview

This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.

Strictly Necessary Cookies

Strictly Necessary Cookie should be enabled at all times so that we can save your preferences for cookie settings.

Powered by  GDPR Cookie Compliance